RAV4 PAB4-Toyota Toyota
1. Car operation
2. Maintenance
3. Engines
   Engine 3S-FE repair without its removal from the car
      General information
      Specifications
      Installation of the piston of the first cylinder in the top dead point (VMT)
      Cover of a head of the block of cylinders
      Inlet collector
      Final collector
      Gear belt and pulleys of a gear belt
      Forward sealing ring of a cranked shaft
      Sealing ring of a camshaft
      Camshafts and pushers of valves
      Head of the block of cylinders
      Oil pallet
      Oil pump
      Drive flywheel / plate
      Back sealing ring of a cranked shaft
      Support of the power unit
   Engine 1AZ-FE repair without its removal from the car
   Diagnostics and preparation of the engine for major maintenance
4. Cooling and conditioning systems
5. Fuel system and system of production of the fulfilled gases
6. Ignition system
7. The monitoring system and decrease in toxicity of the fulfilled gases
8. Coupling
9. Transmission
10. Driveshaft and shaft of a drive of driving wheels
11. Brake system
12. Suspension bracket
13. Steering and running gear
14. Body
15. Electric equipment
Electric equipment schemes




Toyota RAV4>> Engines>> Engine 3S-FE repair without its removal from the car>> Oil pallet
Removal
Removal make in the following order:
– switch off ignition and disconnect a "weight" wire from the storage battery;
– tighten the parking brake and establish an emphasis under back wheels;
– lift a forward part of the car and establish on support;
– remove an antisplash guard of a motor compartment;
– merge from the engine engine oil and turn out the oil filter;
– remove the index (щуп) oil level;
– turn out 3 nuts of fastening of a reception exhaust pipe to a final collector and 2 bolts of fastening of the catalyst to other part of system of production of the fulfilled gases;
– turn out 2 bolts of fastening of an arm and remove a reception exhaust pipe together with an arm;
– remove a support of a final collector;

Fig. 3.37. Arrangement of bolts of fastening of a forward support of the power unit


– turn out bolts (fig. 3.37) and remove the forward support of the power unit located about a radiator of system of cooling;
– turn out bolts and remove the oil pallet. If the oil pallet sits strongly, separate it from the block of cylinders, having inserted between them a screw-driver edge, thus do not damage privalochny surfaces of the pallet and the block of cylinders.
Installation
Firm plastic or wooden scraper clear of the remains of old laying and hermetic privalochny surfaces of the oil pallet and the block of cylinders.
Check that carving openings for bolts of fastening of the oil pallet in the block of cylinders pure and have no carving damages.
Check a flange of the oil pallet, especially about openings for bolts, on lack of the deformed sites. If necessary level a privalochny surface of the pallet a hammer on wooden whetstone.
Check fastening of a maslozaborny tube and lack of cracks in it. If the maslozaborny tube acted in film, clear it and establish with a new sealing ring or laying. Check on absence of pollution the mesh filter of a maslozabornik.

Fig. 3.38. Places of drawing of a layer of RTV hermetic on a privalochny surface of the oil pallet: And — in a groove on a flange; In — round an opening


Put on a privalochny surface of the oil pallet a RTV hermetic layer in diameter of 5 mm (fig. 3.38) .
Establish the oil pallet on the block of cylinders and fix bolts, tightening them consistently around in some passes.
Further installation is carried out to sequences, return to removal, taking into account the following.
Before filling of engine oil wait 1 h in order that hermetic managed to harden.

       NOTE
It is necessary to establish the oil pallet during 5 mines after hermetic drawing.

Establish the new oil filter and fill in in the engine engine oil.
At installation of a reception exhaust pipe use new laying.
Start up the engine and check on absence of leaks.