RAV4 PAB4-Toyota Toyota
1. Car operation
2. Maintenance
3. Engines
4. Cooling and conditioning systems
5. Fuel system and system of production of the fulfilled gases
6. Ignition system
7. The monitoring system and decrease in toxicity of the fulfilled gases
8. Coupling
9. Transmission
10. Driveshaft and shaft of a drive of driving wheels
11. Brake system
12. Suspension bracket
13. Steering and running gear
14. Body
   General information
   Care of a body
   Care of an upholstery and rugs
   Repair of insignificant damages of a body
      Processing of scratches of a body
      Repair of dents of a surface of a body
      Shpaklevka and body painting
   Repair of considerable damages of a body
   Service of hinges and locks
   Recommendations about replacement of a windscreen and motionless glasses
   Removal and cowl installation
   Lock and cable of opening of the lock of a cowl
   Removal and installation of bumpers
   Removal and installation of forward wings
   Removal and installation of facing of the Radiator
   Removal and installation of the deflector of a ventilating lattice
   Removal and installation of an upholstery of doors
   Doors
   Removal and installation of glasses of doors
   Removal and installation of window regulators
   Removal and installation of an external rear-view mirror
   Removal and installation of an internal rear-view mirror
   Door of a luggage compartment
   Removal and installation of the central console
   Removal and installation of elements of furnish of the dashboard
   Removal and installation of casings of a steering column
   Removal and dashboard installation
   Removal and installation of seats
   Adjustment of the elevating and movable panel of a roof
15. Electric equipment
Electric equipment schemes




Toyota RAV4>> Body>> Repair of insignificant damages of a body>> Shpaklevka and body painting
At performance of shpaklevochny works it is necessary to have a wide flexible plastic or nylon shpatel for giving of smoothness of a surface of a shpaklevka. At works on a shpaklevaniye of a body adhere to the following recommendations:
Level a shpaklevka on the damaged site of a body so that to form it demanded and smoothness.
As soon as it was possible to achieve approximately demanded contour, stop to smooth down a shpaklevka a shpatel as at too long smoothing down it will start to harden, stick on a shpatel and to roll down, therefore the surface will be damaged.
Put the subsequent, thinner layer of a shpaklevka, only after drying of the previous layer and so until level of a shpaklevka will not start to act slightly over a processed site.
After shpaklevka hardening its surplus remove with a metal scraper or a file.
Further processing make, using at the first stage a coarse-grained emery paper, then fine-grained. An emery paper have on flat wooden whetstone, differently it will be impossible to achieve an equal surface.
At a finishing stage of polishing it is necessary to moisten a waterproof emery paper with water periodically. It will give to the processed puttied surface special smoothness.
The puttied dent should appear surrounded on perimeter a layer of pure metal. For removal of a dust and fats wash out a processed site water and wipe fat-free means.
Raise dust on a site a thin layer of light soil. It will help to reveal all defects allowed at processing in a shpaklevka. Level them by means of a new layer of a shpaklevka and again зашкурьте a surface.
After that the area of repair is ready to final painting.
Aerosol drawing of paint should be carried out in the warm, dry, windless and easy atmosphere.
At carrying out painting indoors moisten a floor of a working platform with water for hit prevention in dust air. When coloring of only one panel, other parts of a body should be covered from paint hit on them with the newspaper attached by a sticky tape.
Before first coat drawing carefully mix it, put on a trial surface and achieve that it laid down evenly. Put a thick layer of a first coat for what put some thin layers.
Polish the grounded surface a waterproof emery paper. Thus do not forget сбрызгивать ground area water and periodically to moisten in water an emery paper.
Before further painting dry up a processed site.
Put a paint coat with a spray. The necessary thickness of a paint coat is reached by drawing of several thin layers.
Coloring begin from the center of a processed surface and move to edges back and forth motions until all painted surface and area at distance about 20 mm round it will not be painted.
Protective film and newspapers remove later 10–15 минпосле drawings of the last paint coat.
Give the chance to fresh paint to harden within at least two weeks, then by means of an obnovitel of paint or thin abrasive polishing paste level edges of the painted area to level of old paint.
Polish a surface.