RAV4 PAB4-Toyota Toyota
1. Car operation
2. Maintenance
3. Engines
4. Cooling and conditioning systems
5. Fuel system and system of production of the fulfilled gases
6. Ignition system
7. The monitoring system and decrease in toxicity of the fulfilled gases
8. Coupling
9. Transmission
10. Driveshaft and shaft of a drive of driving wheels
11. Brake system
12. Suspension bracket
13. Steering and running gear
14. Body
   General information
   Care of a body
   Care of an upholstery and rugs
   Repair of insignificant damages of a body
   Repair of considerable damages of a body
   Service of hinges and locks
   Recommendations about replacement of a windscreen and motionless glasses
   Removal and cowl installation
   Lock and cable of opening of the lock of a cowl
   Removal and installation of bumpers
   Removal and installation of forward wings
   Removal and installation of facing of the Radiator
   Removal and installation of the deflector of a ventilating lattice
   Removal and installation of an upholstery of doors
   Doors
   Removal and installation of glasses of doors
   Removal and installation of window regulators
   Removal and installation of an external rear-view mirror
   Removal and installation of an internal rear-view mirror
   Door of a luggage compartment
   Removal and installation of the central console
   Removal and installation of elements of furnish of the dashboard
   Removal and installation of casings of a steering column
   Removal and dashboard installation
   Removal and installation of seats
   Adjustment of the elevating and movable panel of a roof
15. Electric equipment
Electric equipment schemes




Toyota RAV4>> Body>> Lock and cable of opening of the lock of a cowl
       PREVENTION
Cars are equipped with the systems of safety (SRS) including safety cushions and natyazhitel of seat belts. Before work about sensors of blow, the dashboard and a steering column disconnect at first negative, and then positive the plug from the storage battery and wait for 2 minutes. It will exclude unauthorized disclosure of safety cushions and operation of natyazhitel of seat belts which can put injuries.

Removal of the lock of a cowl make in a sledushchy way:

Fig. 14.2. Arrangement of bolts of fastening of the lock of a cowl


Marker note the provision of bolts of fastening of the lock of a cowl (see fig. 14.2 ). Turn out bolts and remove the lock from the forward cross-section panel.

Fig. 14.3. A detachment of a cover of a cable from the case of the lock of a cowl


Disconnect a cable cover from the case of the lock of a cowl and a cable from a lock latch (fig. 14.3) .
Installation make in sequence, return to removal, taking into account the following: adjust position of the lock so that gaps between a forward part of a cowl and wings were identical, and a rubber emphasis when closing a cowl was slightly compressed.
Removal of a cable of opening of the lock of a cowl make in a sledushchy way:
In salon of the car remove the panel of an upholstery located under the dashboard from the driver.

Fig. 14.4. A cable detachment from the handle of opening of a cowl: And — a place of fastening of a cover of a cable; In — a place of fastening of a cable to the squeezing lever; With — a clamp


Lift the handle of opening of a cowl up and disconnect a cable cover from a handle arm, then disconnect a cable from the squeezing lever (fig. 14.4) .
If squeezing the lever with the handle will be replaced, pull the handle outside and press down for removal from a clamp and its detachment from the dashboard.
Adhere to a cable a thin long cord. Further the cord is required for retraction to the place of a cable of opening of a cowl.
In a motor compartment disconnect a cable and a cable cover from the cowl lock. Release a cable from clips on a forward cross-section beam and along a wing.
Extend a cable in a motor compartment, before emergence of a cord, then untie a cord from an old cable and fix it on a new cable.
For a cord stretch a new cable through a partition of a motor compartment while it will not reach the handle of opening of a cowl, then untie a cord.
In salon of the car connect a cable to the squeezing lever, and a cover of a cable fix on a handle arm.
If at installation of a cable the condensing ring was displaced from a partition of a motor compartment, fingers of a hand establish it into place.
Further installation make in sequence, return to removal.