RAV4 PAB4-Toyota Toyota
1. Car operation
2. Maintenance
3. Engines
4. Cooling and conditioning systems
5. Fuel system and system of production of the fulfilled gases
6. Ignition system
7. The monitoring system and decrease in toxicity of the fulfilled gases
8. Coupling
9. Transmission
10. Driveshaft and shaft of a drive of driving wheels
11. Brake system
12. Suspension bracket
13. Steering and running gear
14. Body
   General information
   Care of a body
   Care of an upholstery and rugs
   Repair of insignificant damages of a body
   Repair of considerable damages of a body
   Service of hinges and locks
   Recommendations about replacement of a windscreen and motionless glasses
   Removal and cowl installation
   Lock and cable of opening of the lock of a cowl
   Removal and installation of bumpers
   Removal and installation of forward wings
   Removal and installation of facing of the Radiator
   Removal and installation of the deflector of a ventilating lattice
   Removal and installation of an upholstery of doors
   Doors
   Removal and installation of glasses of doors
   Removal and installation of window regulators
   Removal and installation of an external rear-view mirror
   Removal and installation of an internal rear-view mirror
   Door of a luggage compartment
   Removal and installation of the central console
   Removal and installation of elements of furnish of the dashboard
   Removal and installation of casings of a steering column
   Removal and dashboard installation
   Removal and installation of seats
   Adjustment of the elevating and movable panel of a roof
15. Electric equipment
Electric equipment schemes




Toyota RAV4>> Body>> Removal and cowl installation
Removal of a cowl carry out in a sledushchy way:
Open a cowl and enclose pure rags under its corners to protect a paint and varnish covering of the car at cowl removal.
Disconnect from a washer nozzle a hose and electric sockets.
Adhere to a hose and the electric socket a thin long cord.
Extend from a cowl electroconducting and a hose, untie from them a cord, leave it in a cowl. Further the cord is required for installation in an electroconducting and hose cowl.

Fig. 14.1. Arrangement of bolts of fastening of the hinge of a cowl


Marker note position of hinges on a cowl (fig. 14.1) .
Ask the assistant to support a cowl in open situation, turn out bolts of fastening of the left and right hinges of a cowl and, being careful, remove a cowl.
Installation of a cowl make in sequence, return to removal, taking into account the following:
With two assistants establish a cowl and twirl by hand bolts of fastening of hinges of a cowl.
Level cowl hinges according to earlier made labels and tighten bolts of fastening of a cowl.
Adjustment of a cowl make in a sledushchy way:
Close a cowl and check its provision of rather adjacent surfaces. For adjustment weaken bolts of fastening of loops of a cowl and, moving a cowl, adjust its situation.
After adjustment tighten bolts of fastening of loops of a cowl.

       NOTE
It is necessary to mean that the bolts established at plant, do not allow to carry out adjustment therefore for performance of adjustment replace these bolts standard with flat lock washers.

Marker note position of hinges on a cowl to know, on what distance to move a cowl.
After adjustment close a cowl and check its provision of rather adjacent surfaces.
For adjustment of a forward part of a cowl on height, and also for adjustment of gaps between a forward part of a cowl and wings it is possible to change position of the lock of a cowl.

Fig. 14.2. Arrangement of bolts of fastening of the lock of a cowl


Marker note the provision of bolts of fastening of the lock of a cowl (fig. 14.2) . Weaken bolts and, moving the lock, establish it in situation at which gaps between a forward part of a cowl and wings will be identical and uniform on all length.
After adjustment tighten bolts of fastening of the lock of a cowl.       
Adjustment of height of installation of a forward part of a cowl carry out, rolling or turning out the rubber emphasis located on each side on the forward cross-section panel on models till 2001 and in a forward part of a cowl on models since 2001, and also adjustment of position of the lock of a cowl. For increase in height of installation of a cowl a rubber emphasis rotate clockwise, and for reduction — counter-clockwise.