RAV4 PAB4-Toyota Toyota
1. Car operation
2. Maintenance
3. Engines
4. Cooling and conditioning systems
5. Fuel system and system of production of the fulfilled gases
6. Ignition system
7. The monitoring system and decrease in toxicity of the fulfilled gases
8. Coupling
9. Transmission
   General information
   Specifications
   Transmission repair
   The repair and adjusting work which is carried out on cars with a mechanical transmission
   The repair and adjusting work which is carried out on cars with an automatic transmission
      Diagnostics of an automatic transmission
      Replacement of sealing cuffs
      Check, adjustment and replacement of a cable of management with a butterfly valve
      Replacement and adjustment of a cable of the selector
      Replacement and adjustment of the switch of blocking of a starter (PNP)
      Check of system of blocking of the lever of the selector and ignition lock
      Removal and installation of an automatic transmission on models with one leading bridge
      Removal and installation of an automatic transmission on all-wheel drive models
10. Driveshaft and shaft of a drive of driving wheels
11. Brake system
12. Suspension bracket
13. Steering and running gear
14. Body
15. Electric equipment
Electric equipment schemes






Toyota RAV4>> Transmission>> The repair and adjusting work which is carried out on cars with an automatic transmission>> Removal and installation of an automatic transmission on models with one leading bridge
Removal
Switch off ignition and disconnect a "weight" wire from the storage battery.
Remove a cowl.
Remove a broad tank.
On release models till 2001 weaken a lock-nut and remove a cable cover from an arm of throttle knot. Disconnect a cable from butterfly valve sector.
Remove a starter.
Mark and disconnect all electric sockets from a transmission.
Unscrew a bolt of fastening of a wire of "weight".
Turn out bolts of fastening of a transmission available from above to the engine.
Establish over a motor compartment a cross-piece and a chain for an eye fix a transmission to a cross-piece.
Turn out a bolt of fastening of the left support of a transmission.
Weaken nuts of fastening of power shafts to naves of forward wheels.
Tighten the parking brake and block back wheels. Lift a forward part of the car and establish it on support. Remove forward wheels.
Remove a mudguard of a motor compartment.
Unscrew a nut of fastening of a cable of the selector and disconnect it from the lever of a choice of transfers on the forward party of a transmission.
Remove a clip and remove a cable cover from an arm on a transmission.
Merge transmission liquid from a transmission.
Remove power shafts.
Remove a reception exhaust pipe.
Mark and disconnect all electric sockets available from below from a transmission.
Disconnect from a transmission the hoses going to an oil radiator. Close the ends of hoses plastic jams.
Turn out a bolt of fastening of the steering mechanism to the bottom cross-section beam. A soft wire fix steering transfer on a beam established across a motor compartment.
On models since 2001 remove a cap, closing an opening for access to the hydrotransformer, then paint note position of the hydrotransformer and a drive plate.
On models 1996 and 1997 of years disconnect a selector cable from the bottom cross-section beam.
On models since 2001 disconnect earrings of the stabilizer of cross-section stability from the stabilizer.
Remove the bottom cross-section and longitudinal beams.

Fig. 9.29. Arrangement of bolts of fastening of a plate of rigidity


On models till 2001 turn out bolts and remove a rigidity plate (fig. 9.29) .
On models till 2001 paint note position of the hydrotransformer and a drive plate.
Turn out bolts of fastening of the hydrotransformer. For access to each subsequent bolt turn a cranked shaft of the engine in the direction of its working rotation for the central bolt of fastening of a pulley of a cranked shaft.
Support a transmission a transmission jack.
Turn out the remained bolts of fastening of a transmission to the engine, thus note an arrangement of bolts as they have various length.
Take away a transmission from the engine and check that the hydrotransformer is separated from a drive plate. Captures fix the hydrotransformer, lower and remove a transmission.
Installation
Installation make in sequence, return to removal taking into account the following.
Combine labels on the hydrotransformer and the drive plate, put before removal.
Fill in transmission liquid in a transmission.
Adjust a selector cable, and a cable of management of a butterfly valve (on models till 2001).