RAV4 PAB4-Toyota Toyota
1. Car operation
2. Maintenance
3. Engines
4. Cooling and conditioning systems
5. Fuel system and system of production of the fulfilled gases
6. Ignition system
7. The monitoring system and decrease in toxicity of the fulfilled gases
8. Coupling
9. Transmission
10. Driveshaft and shaft of a drive of driving wheels
11. Brake system
12. Suspension bracket
13. Steering and running gear
   General information
   Technical characteristics
   Removal and installation of a steering wheel with a safety cushion
   Removal and installation of a steering column
   Removal and installation of tips of steering drafts
   Replacement of covers of the steering mechanism
   Removal and installation of the steering mechanism
   Removal and installation of the pump of the amplifier of a steering
   Pumping of hydraulic system of the amplifier of a steering
   Replacement of bolts of fastening of a wheel
   Wheels and tires
14. Body
15. Electric equipment
Electric equipment schemes




Toyota RAV4>> Steering and running gear>> Removal and installation of the pump of the amplifier of a steering
Removal of the pump of the amplifier of a steering for models till 2001 make as follows.
Switch off ignition and disconnect a "weight" wire from the storage battery.
Syringe pump out liquid from a tank of the amplifier of a steering.
Establish under a motor compartment the reception pallet for collecting liquid.
Tighten the parking brake and block back wheels an emphasis.
Lift the car on the lift, remove protection of a motor compartment.
Remove forward section of system of production of the fulfilled gases.

Fig. 13.15. An arrangement of the left bolts of fastening of a cross-section beam on models till 2001


Remove tips of steering drafts from rotary fists and turn out a bolt of fastening of the steering mechanism to a cross-section beam, then turn out bolts and remove a cross-section beam of a forward suspension bracket (see fig. 13.15 ).

Fig. 13.17. Arrangement of sharnirny and tightening bolts of fastening of the pump of the amplifier of a steering


Weaken sharnirny and tightening bolts, move the pump of the amplifier of a steering to the engine and remove a belt of a drive of the pump (fig. 13.17) .
Weaken a collar and disconnect a hose of return of liquid from the pump;

Fig. 13.18. A reversing of the union of a delivery hose (1) from the pump of the amplifier of a steering


cap key turn out the union of a delivery hose from the pump (fig. 13.18) .
Disconnect two vacuum hoses from the pump.

Fig. 13.19. An arrangement of bolts of fastening of an arm of the pump of the amplifier of a steering on models till 2001


Turn out bolts of fastening of an arm of the pump and remove the pump (fig. 13.19) ;
if necessary turn out nuts and remove the pump from an arm.
Installation of the pump carry out to sequences, return to removal, taking into account the following.
Adjust tension of a belt of a drive of the pump.
Add liquid in a tank of the amplifier of a steering and remove air from hydraulic system.
Removal of the pump of the amplifier of a steering for models since 2001 make as follows:
Switch off ignition and disconnect a "weight" wire from the storage battery.
Syringe pump out liquid from a tank of the amplifier of a steering.
Establish under a motor compartment the reception pallet for collecting liquid.
Remove a belt of a drive of the pump of the amplifier of a steering.
Tighten the parking brake and block back wheels an emphasis.
Weaken nuts of fastening of the right forward wheel.
Lift a forward part of the car and establish on support.
Remove the right forward wheel and an antisplash guard of an arch of the right forward wheel.
Disconnect the electric socket from the sensor of pressure of the amplifier of a steering.
Turn out a hollow bolt and disconnect a delivery hose from the pump.
Weaken a collar and disconnect a hose of return of liquid from the pump.

Fig. 13.20. An arrangement top (In) and bottom (And) bolts of fastening of the pump of the amplifier of a steering on models since 2001


Turn out the bottom bolt, then weaken the top bolt and remove the pump of the amplifier of a steering from the engine (fig. 13.20) .
Installation of the pump carry out to sequences, return to removal, taking into account the following:
At installation of a hollow bolt of fastening of a delivery hose use new sealing laying.
Establish a wheel, screw nuts, lower the car and tighten nuts of fastening of a wheel.
Establish a belt of a drive of the pump and adjust its tension.
Add liquid in a popolnitelny tank of the amplifier of a steering and remove air from hydraulic system.