RAV4 PAB4-Toyota Toyota
1. Car operation
2. Maintenance
3. Engines
4. Cooling and conditioning systems
5. Fuel system and system of production of the fulfilled gases
   General information
   Technical characteristics of system of injection of fuel
   Sbrasyvaniye of pressure in fuel system
   General check of fuel system
   Fuel pump
   Regulator of pressure of fuel
   Fuel level sensor
   Fuel tank
   Case of the air filter
   Accelerator cable
   Electronic system of injection of fuel
   Damper of pulsations of fuel on models since 2001
   Distributive fuel highway and nozzles
   System of production of the fulfilled gases
6. Ignition system
7. The monitoring system and decrease in toxicity of the fulfilled gases
8. Coupling
9. Transmission
10. Driveshaft and shaft of a drive of driving wheels
11. Brake system
12. Suspension bracket
13. Steering and running gear
14. Body
15. Electric equipment
Electric equipment schemes






Toyota RAV4>> Fuel system and system of production of the fulfilled gases>> Distributive fuel highway and nozzles
Removal of the distributive fuel highway and nozzles make as follows:
Dump pressure in fuel system.
Switch off ignition and disconnect a "weight" wire from the storage battery.
On models till 2001 further operations carry out as follows:
– uncover heads of the block of cylinders;
– remove throttle knot;

Fig. 5.28. The distributive fuel highway and nozzles of models till 2001: 1–sealing ring; 2–insulator; 3–nozzle; 4–rubber plug; 5–sealing ring; 6–rasporny plug; 7–electric socket; 8–plait of wires; 9–air tube; 10-distributive fuel highway; 11-the valve of system of a retsirkulyatsiya of the fulfilled gases; 12-a hose of system of a retsirkulyatsiya of the fulfilled gases; 13-vacuum hose; 14-vacuum hose; 15-laying; 16-throttle knot; 17-nut; 18th bolts; 19-hose of compulsory ventilation of a case; 20-laying


– release 2 clips and disconnect a plait of wires from an inlet collector (fig. 5.28) ;
– disconnect 4 electric sockets from nozzles;
– remove a protective plate on the right side of an inlet collector;
– remove the valve and a tube of system of a retsirkulyatsiya of the fulfilled gases;
– turn out a hollow bolt from the top part of the fuel filter and disconnect from it a fuel hose;
– disconnect a vacuum hose of the vacuum amplifier of brakes from an inlet collector;
– disconnect fuel tubes from the distributive fuel highway;

Fig. 5.29. An arrangement of bolts of fastening of the distributive fuel highway on models till 2001


– turn out bolts and remove the distributive fuel highway together with nozzles (fig. 5.29) ;

Fig. 5.30. Removal of nozzles from the distributive fuel highway on models till 2001


– having pulled and at the same time turning, remove nozzles from the distributive fuel highway (fig. 5.30) ;
– if nozzles are repeatedly established, replace with them sealing rings;
On models since 2001 further operations carry out as follows:
– disconnect a hose from the valve of compulsory ventilation of a case;

Fig. 5.31. The distributive fuel highway and nozzles of models since 2001: 1–hose of compulsory ventilation of a case; 2–distributive fuel highway; 3–rasporny plug; 4–sealing ring; 5–electric socket; 6–nozzle; 7–laying


– disconnect fuel tubes from the distributive fuel highway (fig. 5.31) ;

Fig. 5.32. An arrangement of bolts of fastening of the distributive fuel highway on models since 2001


– turn out bolts of fastening of the fuel highway (fig. 5.32) ;
– remove the distributive fuel highway together with nozzles;

Fig. 5.33. Removal of nozzles from the distributive fuel highway on models since 2001


– having pulled and at the same time turning, remove nozzles from the distributive fuel highway (fig. 5.33) ;
– if nozzles are repeatedly established, replace with them sealing rings.
Installation carry out to sequences, return to removal.