Removal of a fuel tank make as follows.

Dump pressure in fuel system.

Remove a stopper from a jellied mouth of a fuel tank therefore pressure in a fuel tank will be leveled with the atmospheric.

Switch off ignition and disconnect a "weight" wire from the storage battery.

If in a fuel tank there is a fuel, pump out it. Pumping out of fuel carry out the special pump.

Lift the car on the lift.

Remove back and central parts of system of production of the fulfilled gases.

On all-wheel drive cars remove the driveshaft.

Fig. 5.16. Places of connection of fuel pipelines and a return tube паров fuels to a fuel tank

Disconnect from a fuel tank fuel pipelines, a return tube паров fuels and a jellied mouth (fig. 5.16) . Close fuel pipelines plastic jams that will exclude an effluence of fuel and pollution of fuel system.

Jack, through wooden whetstone support a fuel tank.

Fig. 5.17. Arrangement of bolts of fastening of basic tapes of a fuel tank

Fig. 5.18. A fuel tank of cars till 2001 of release: 1–laying; 2–block of the fuel pump/fuel level sensor; 3–clamp of fastening of a tube; 4–cover of a fuel tank; 5–laying; 6–main tube of a fuel tank; 7–valve of control of filling; 8–fuel level sensor; 9–protective cover of the valve of control of filling; 10-thick fuel pipe; 11-a tube for air removal; 12-protective plate; 13-tube; 14-jellied mouth; 15-jellied mouth; 16-cover of a jellied mouth; 17-lock ring; 18-collars; 19-inlet fuel hose; 20-protective plate; 21-fuel tank; 22-basic tape of a fuel tank; 23-protective plate; 24-protective plates

Turn out bolts of fastening of basic tapes of a fuel tank (fig. 5.17, 5.18) .

Lower a fuel tank so that it was possible to disconnect the electric socket from the block of the fuel pump/fuel level sensor.

Take a fuel tank from under the car.

PREVENTION Even in an empty fuel tank there are pairs of fuel which are explosive therefore be careful.

Any repair of a fuel tank or jellied mouth should be carried out by the expert who has experience of performance of critical and potentially dangerous works. Even after cleaning and washing of a fuel tank in it there are explosive pairs of fuel.

On cars of later releases the fuel tanks made of plastic which are not subject to repair are established.

The removed fuel tank should be located far from open fire, the scintillating devices, open fire-dangerous light devices and smoking places.

Installation of a fuel tank carry out to sequences, return to removal.

Fig. 5.19. The air filter on models till 2001: 1–accelerator cable; 2–tank of hydraulic system of the amplifier of a steering; 3–a filtering element of the air filter; 4–broad tank; 5–relay of control of sliding; 6–the electric socket of the sensor of temperature of air arriving in the engine; 7–hose of compulsory ventilation of a case (PCV); 8–high-voltage wires; 9–air hose; 10-cover of the air filter; 11-case of the air filter; 12-relay No. 2 block; 13-cable of management of a butterfly valve; 14-laying; 15-tube of supply of fuel; 16-laying

Fig. 5.20. The air filter on models since 2001: 1–coil of ignition; 2–electric socket of the coil of ignition; 3–case of the air filter; 4–a filtering element of the air filter; 5–arm of the air filter

Removal and installation of the case of the air filter make as follows (fig. 5.19 and 5.20) :

Release spring clips and uncover and a filtering element of the air filter.

On models till 2001 disconnect the electric socket from the relay of control of the sliding placed sideways of a cover of the air filter.

On models since 2001 disconnect an air inlet branch pipe from a cover of the air filter.

Fig. 5.21. Arrangement of screws of fastening of the case of the air filter

Turn out 3 screws and remove the case of the air filter (fig. 5.21) .

Installation of the case of the air filter carry out to sequences, return to removal.

Installation of the case of the air filter carry out to sequences, return to removal.